Continual is The brand by HMF Company with experience, which manifactures and distributes Truck Spare Parts and passanger cars too. HMF's brand: CONTINUAL ( quality assured ISO 9001:2008 brand ) we have accumulated our basic capital, namely professional knowledge and experience which we consider as guarantee of our success. We supply production, distribution and sale of BRAKE CALIPER repair kits for trucks , Bus and more.
Before Reading information Below
Have Fun with above
Air brake systems are typically used on heavy trucks and buses. The system consists of service brakes, parking brakes, a control pedal, and an air storage tank. For the parking brake, there is a disc or drum brake arrangement which is designed to be held in the 'applied' position by spring pressure. Air pressure must be produced to release these "spring brake" parking brakes. For the service brakes (the ones used while driving for slowing or stopping) to be applied, the brake pedal is pushed, routing the air under pressure (approx 100–120 psi or 690–830 kPa) to the brake chamber, causing the brake to be engaged. Most types of truck air brakes are drum brakes, though there is an increasing trend towards the use of disc brakes in this application. The air compressor draws filtered air from the atmosphere and forces it into high-pressure reservoirs at around 120 psi (830 kPa). Most heavy vehicles have a gauge within the driver's view, indicating the availability of air pressure for safe vehicle operation, often including warning tones or lights. Setting of the parking/emergency brake releases the pressurized air in the lines between the compressed air storage tank and the brakes, thus allowing the spring actuated parking brake to engage. A sudden loss of air pressure would result in full spring brake pressure immediately.
A compressed air brake system is divided into a supply system and a control system. The supply system compresses, stores and supplies high-pressure air to the control system as well as to additional air operated auxiliary truck systems (gearbox shift control, clutch pedal air assistance servo, etc.).
Highly simplified air brake diagram on a commercial road vehicle (does not show all air reservoirs and all applicable air valves).
The air compressor is driven by the engine either by crankshaft pulley via a belt or directly from the engine timing gears. It is lubricated and cooled by the engine lubrication and cooling systems. Compressed air is first routed through a cooling coil and into an air dryer which removes moisture and oil impurities and also may include a pressure regulator, safety valve and smaller purge reservoir. As an alternative to the air dryer, the supply system can be equipped with an anti-freeze device and oil separator. The compressed air is then stored in a reservoir (also called a wet tank) from which it is then distributed via a four way protection valve into the front and rear brake circuit air reservoir, a parking brake reservoir and an auxiliary air supply distribution point. The system also includes various check, pressure limiting, drain and safety valves.
Air brake systems may include a wig wag device which deploys to warn the driver if the system air pressure drops too low.
The control system is further divided into two service brake circuits: the parking brake circuit and the trailer brake circuit. This dual brake circuit is further split into front and rear wheel circuits which receive compressed air from their individual reservoirs for added safety in case of an air leak. The service brakes are applied by means of a brake pedal air valve which regulates both circuits. The parking brake is the air operated spring brake type where its applied by spring force in the spring brake cylinder and released by compressed air via hand control valve. The trailer brake consists of a direct two line system: the supply line (marked red) and the separate control or service line (marked blue). The supply line receives air from the prime mover park brake air tank via a park brake relay valve and the control line is regulated via the trailer brake relay valve. The operating signals for the relay are provided by the prime mover brake pedal air valve, trailer service brake hand control (subject to a country's relevant heavy vehicle legislation) and the prime mover park brake hand control.
Park brake valve
Spring brake cylinder
Air brake foot valve
Trailer brake relay valve
Truck air compressor
Air brake relay valve
Four way protection valve
Air brakes are used as an alternative to hydraulic brakes which are used on lighter vehicles such as automobiles. Hydraulic brakes use a liquid (hydraulic fluid) to transfer pressure from the brake pedal to the brake shoe to stop the vehicle. Air brakes have several advantages for large multitrailer vehicles:
The supply of air is unlimited, so the brake system can never run out of its operating fluid, as hydraulic brakes can. Minor leaks do not result in brake failures.
Air line couplings are easier to attach and detach than hydraulic lines; there is no danger of letting air into a pneumatic circuit. So air brake circuits of trailers can be attached and removed easily by operators with little training.
Air not only serves as a fluid for transmission of force, but also stores potential energy. So it can serve to control the force applied. Air brake systems include an air tank that stores sufficient energy to stop the vehicle if the compressor fails.
Air brakes are effective even with considerable leakage, so an air brake system can be designed with sufficient "fail-safe" capacity to stop the vehicle safely even when leaking.
Driving technique and operator licensing
As air brakes must be operated differently from more common hydraulic systems, most countries require additional training and licensing in order to legally drive any vehicle using an air brake system.
Driving a vehicle with air brakes requires basic knowledge of proper maintenance as well. A driver is required to inspect the air pressurization system prior to driving and make sure all tanks are in working order. In addition, the manner of applying brakes is usually different from regular hydraulic type systems. Pressure is applied slowly and air levels must be monitored at all times as a loss in air pressure will result in brake lockup aka "dynamiting". Unlike hydraulic brakes, air brakes must not be pumped repeatedly as the repetitive application and release of air will drain the system prematurely
We have just updated Our Produst List For You with More OE numbers to check
As You know that We have Knorr Type,Meritor Type,Haldex Type, Wabco Type, Z Cam Type , Brembo Type Caliper Repair Kits For Truck, Bus and Heavy Duty Vehicles And Vans,
Here is some informaation Regarding Knorr Types We have.,
You can Visit Our ShowRoom and Office in Istanbul
As You Know We have Showroom in istanbul. You can stop by for a Turkish Tea Or Coffie Any Time and see all our product line.
We can supply You
Wabco, Meritor , Knorr, Haldex, Z Cam and More Truck Bus ,Van's Brake Caliper Repair Kits ans systems
Sales and international Relations
We have Showroom in Istanbul We have Factory in KONYA ,
We would like you to invite again our showroom or Factory
Our Locations are very simple.
Our Office in Istanbul
Adres : İkitelli Organize Sanayi Bölgesi Dolapdere Sanayi Sitesi 2.ada No: 2 İKİTELLİ-BAŞAKŞEHİR / İSTANBUL / TURKEY
Telefon : +90-212 671 68 23
Faks : +90-212 671 68 30
E-Posta : firstname.lastname@example.org
Adres : Fevzi Çakmak Mahallesi Büsan Ozel Organize Sanayi Sitesi 10664 Sokak No:31/D Karatay/KONYA/TURKEY
With our New Office in istanbul , Whenever you are in istanbul , you can visit us. Our Office is 30 Minutes from Airport and Tuyap Fair Ground. You can Come to Our Office with Subway/Metro/Tram, We are very Close To Public Transport. Continual Brand is owned by HMF Company.
Need inspiration for your Business of Caliper Repair Kits ? Just Click Here to see our Web Page.
You Can Also Visit Our Google Drive Pages For Catalogs and more!
HMF Is a Company with experience, which manifactures and distributes Truck Spare Parts and passanger cars too. HMF's brand: CONTINUAL ( quality assured ISO 9001:2008 brand ) we have accumulated our basic capital, namely professional knowledge and experience which we consider as guarantee of our success. We supply production, distribution and sale of BRAKE CALIPER repair kits for trucks (such as Mercedes, Volvo, Daf, Scania, Iveco,Renault, Mercedes Sprinter, passenger cars etc)
LINE LOURD. Camion et autobus, Étrier de frein KITS DE REPARATION,. des pièces de rechange
HEAVY LINE. ,LORRY Truck and bus, caliper brake repair KITS. spare parts
DIKKE LIJN. VRACHTWAGEN Truck en bus, remklauw rem reparatie KITS. reserveonderdelen